Service

Switchboard upgrades

Switchboard upgrades across Brisbane Northside. Licensed and insured.

Switchboard upgrades work by 97 Electrical

Switchboard upgrades on Brisbane's north side

Your switchboard is the box where the power comes in and gets split up between the lights, the power points, the hot water, the oven and the aircon. Every circuit in the place runs through it. When it's doing its job you never think about it. When it isn't, you get breakers tripping for no good reason, warm plastic, a burnt smell, or whole circuits running with no safety switch on them.

An upgrade means we take the old gear out and fit a new board with modern circuit breakers and safety switches. A safety switch, or RCD, cuts the power in a fraction of a second if current starts leaking where it shouldn't, like through a person holding a faulty kettle. Fuses never did that. A fuse protects the wiring from overload. It does nothing to protect you from a shock. That's the biggest single reason people upgrade a board.

Two kinds of jobs make up most of our board work. The first is an old board that's run out of road: ceramic fuses, fuse wire, a rewireable board, or a mix of breakers added over thirty years with one safety switch covering half the house. Plenty of homes around Strathpine, Petrie and Kallangur still have the board they were built with. The second is a board that copes with today but won't cope with what you're about to add. A split system, a pool pump, an induction cooktop, a shed, solar or an EV charger all need spare capacity, spare ways in the board and the right protection on the new circuit.

Worth being straight about one thing. A new board won't rewire your house. If there's tired cable behind the walls or a light fitting with cooked insulation, a new board doesn't repair it. What it does is find it, because the testing we do at changeover picks up faults an old fuse board was quietly living with.

We're based in Warner and work a tight patch: Albany Creek, Eatons Hill, Warner, Cashmere, Strathpine, Petrie, Kallangur, North Lakes, Mango Hill, Narangba, Burpengary and east to Redcliffe. Houses, units, rentals, and small commercial jobs like shops and sheds. If you're not sure where your board stands, send a photo of it to 0491 105 475 and we'll tell you.

What you notice, and what's actually going on

Hardly anyone rings up asking for a switchboard upgrade. They ring because something's annoying them or something gave them a fright. Here's what usually starts the call.

Breakers or fuses that trip often. One circuit doing it over and over is the wiring telling you something: a failing appliance, water in an outdoor power point, a cooked light fitting, or too much load on a circuit that was never built for it. Guessing is how people get hurt. It needs testing, not a fresh bit of fuse wire.

Ceramic fuses or fuse wire. If you have to unscrew a porcelain plug and fit a thin wire to get the power back, the board is decades old. There's no RCD protection anywhere in the house, and the fuse carriers go brittle and loose with heat.

Scorch marks, brown staining or a burnt smell at the board. That's heat from a loose connection or an overloaded circuit. A terminal heats and cools for years until it works loose, then it starts arcing. Don't sit on that one.

Buzzing, humming, or a board cover that's warm to touch. Same story, same answer.

The board is full. No spare ways left, so nothing new can go in, and often someone has doubled up on a breaker to squeeze in a shed or an aircon circuit.

Tripping when a few things run at once. Older homes were often built with three or four circuits for the whole house. A modern kitchen on its own asks more of a board than that.

What causes all of it here comes down to age, load and weather.

Age first. A lot of the housing stock through Strathpine, Petrie and Kallangur went up when a house had a fridge, a telly and a hot water tank. The board and the circuit count were sized for exactly that. Nothing has changed at the board while everything inside the house has.

Then load. Estate homes around North Lakes and Mango Hill are newer and usually start with a decent board, but they fill up quickly. Two or three split systems, a pool, a workshop out the back, then an EV in the driveway. We check the board and the main supply before any of that gets ordered, because finding out afterwards costs more and holds the whole job up.

And weather. Meter boxes and outdoor boards cop the worst of it. Around Redcliffe and along the bay, salt air gets into an enclosure and eats screws, terminals and hinges. Storms across Moreton Bay bring surges and rain driven sideways, and a cracked enclosure or a perished door seal lets water sit where it shouldn't. We see rust down the backing panel, green on the terminals, and doors that haven't shut properly in years. Geckos and ants nest in warm boards too, which sounds funny right up until one bridges something.

One more thing we'd rather say now than halfway through the day. Some boards from the 1960s and 70s sit on a backing panel that can contain asbestos. If we find one, we stop, tell you, and explain how it gets handled before anyone drills into it.

How the job runs, first call to done

Start with a photo. Open the board cover if you can do it safely, take a photo of the guts of it, then a wider one of the meter box. Text them to 0491 105 475. Most of the time that's enough for us to tell you whether you're looking at a straight board change, a bigger job with mains work, or something that can honestly wait.

Then we come and look. For anything past a simple swap we want eyes on it. We check the main switch and the earthing, look at the condition of the cable insulation where it enters the board, count the circuits, look at the neutral and earth bars, and test whatever protection is already in there. We check the mains coming in and how the meter is set up, because that decides whether the network needs to be involved.

You get a price and a plain explanation of it. What's getting replaced, what we're reusing, how many circuits end up with their own safety switch, whether the mains need upsizing, and anything we found that's a separate job. If a circuit has a fault behind the wall, we tell you about it rather than burying it in the total.

We book a time and tell you how long the power's off. A full board change is usually most of the day, and it moves around with the circuit count and what's behind the panel. You get a likely window before we start, so you can plan around the fridge and freezer, anyone working from home, or gear that needs power. We confirm the day before.

Network work, where it's needed. Some jobs need the supply pulled and reconnected, or the meter moved. That gets arranged with Energex and it changes how the day runs. We explain that up front instead of turning up and dropping it on you.

The install itself. Power off, old gear out, new enclosure mounted with spare ways for later. Circuits get split sensibly instead of lumped together, so one fault doesn't drop your whole house. Cables are dressed properly rather than bundled into a knot, and terminations go up to the right tightness, not by feel.

Testing before the power goes back on. Insulation resistance, earth continuity, polarity, loop impedance, then every safety switch tripped and timed. This is the part people never see and the part that matters most. It's also where the sick circuit usually shows itself.

Labels and paperwork. Every circuit gets labelled so the next person, including you at 10pm with a torch, knows which switch does what. You get a Certificate of Testing and Compliance for the work. We'll send before and after photos too if you want them for a landlord, an agent or your own records.

We clean up. Drop sheet down, swarf and offcuts vacuumed, old board taken away with us.

Last, a walk around the new board. Which switch is which, how to reset a safety switch if it ever trips, and what it means if it trips straight back out. Two minutes, and it saves a phone call later.

Gear and the rules we work to

Boards and protection. We fit din rail enclosures with room to grow, because the board you put in today will need another circuit in a few years. Most circuits get an RCBO, which is a circuit breaker and a safety switch built into one unit on that circuit alone. The benefit is easy to explain: a fault in the bathroom doesn't take the fridge and the lights out with it. We stick with gear from suppliers we can still get matching parts for down the track, instead of the cheapest no-name kit off the internet. Surge protection at the board is worth a conversation if you're in a storm-prone spot or you've got a lot of electronics in the house. Bigger homes and commercial jobs often run three phase, and the same thinking applies to the board layout.

Enclosures. Where the board lives outside, the box matters as much as what's inside it. We use properly rated outdoor enclosures with seals that still seal and glands done up correctly. Older homes up around Albany Creek often have the board on an exposed wall, and closer to the water the enclosure is usually the first thing to go.

Standards. Electrical work in Queensland runs to the Wiring Rules, AS/NZS 3000. That standard covers how a switchboard is built, how circuits are protected, and where RCDs are required. Under the current edition, RCD protection applies to circuits when work is done on them, which is why a board change normally ends with a lot more of your house protected than before. Testing follows the verification guidelines in AS/NZS 3017, which is where trip times and resistance readings come from. The work also sits under Queensland's Electrical Safety Act and Regulation, and anything on the supply side or around the metering follows Energex's connection rules.

Test gear. Insulation resistance tester, loop impedance and RCD tester, and a clamp meter for load readings. Results get written down, not guessed at.

The other standard is ours, and it's simpler. The board has to be readable when we leave. Labels that match reality, the circuit chart filled in, and a cover that sits flat.

When it can't wait

Some board faults are a safety problem right now. If you've got any of these, switch the main switch off and ring us:

  • a burning or hot plastic smell at the board
  • scorch marks, melted plastic or smoke
  • arcing, crackling or a loud buzz
  • a board cover that's hot to touch
  • a safety switch that trips the second you reset it

If there's smoke or you think something's alight, call 000 first. If the power is out across the whole street, or you can see lines down outside, that's the network rather than your board, and the fault number is on your electricity bill.

We're not a 24 hour operation and we won't pretend otherwise. We're on the tools Monday to Friday, 7am to 5pm, and Saturday mornings 7am to 11am. When you ring about an urgent board fault, we'll give you a real time rather than leaving you hanging. Calls get returned.

On an urgent job the first visit is usually about making it safe, not doing the whole upgrade. We isolate the faulty circuit, test to work out where the problem actually is, and get the rest of the house running if that's safe to do. Then the board change gets booked properly and done with the right gear on the van instead of rushed.

If you already know your board is old, don't wait for the smell. A planned upgrade is a booked day with the freezer sorted out beforehand. The other version is a scramble.

Why people on the north side call us

97 Electrical is Jake's business, run out of Warner. He's a licensed electrician and still on the tools every day. No call centre. Ring 0491 105 475 and you're talking to the bloke who'll be doing the job.

We're rated 5.0 on Google. What we aim for on every board is simple: turn up when we say, ring back, explain the job, leave it clean. Small promises, kept.

Knowing the area helps on this job more than people expect. We know what's behind the panel in the older homes around Strathpine, Petrie and Warner, how the estate homes in North Lakes and Mango Hill get loaded up, and what salt air does to a meter box near the water.

You'll get it explained in plain English, once, without the jargon. Trade terms get used because they're the right words, and then said again in normal language. If you'd rather know why something is needed before you agree to it, you're our kind of customer.

Send a photo of your board to 0491 105 475, or give us a call and we'll book a time to look at it. Albany Creek, Eatons Hill, Warner, Cashmere, Strathpine, Petrie, Kallangur, North Lakes, Mango Hill, Narangba, Burpengary and Redcliffe. More at 97electrical.com.au.

Frequently asked questions

How do I know my switchboard needs upgrading?

Look for ceramic fuses or fuse wire, a board with no safety switches, scorch marks or brown staining, buzzing, or breakers that trip often. Older homes around Strathpine, Petrie and Kallangur often still have the original board. Text a photo of it to 0491 105 475 and we'll tell you where it stands.

What does a switchboard upgrade cost?

It depends on the board, how many circuits you have, whether the mains need upsizing, and what's behind the panel. Give us a call on 0491 105 475, send a photo, and we'll talk the job through and quote it properly. We don't guess at prices over the phone without seeing the board.

How long will my power be off?

Most of the day for a full board change, though it varies with the job. We'll give you a likely window before we start so you can plan around the fridge, the freezer and anyone working from home. If someone in the house relies on powered medical gear, tell us when you book and we'll work around it.

Do I need a safety switch on every circuit?

The current Wiring Rules require RCD protection on circuits when work is done on them, so a board change usually ends with far more of the house protected than before. A safety switch cuts the power in a fraction of a second if there's a fault. We'll explain exactly what applies to your board once we've looked at it.

Can you upgrade the board before I get aircon or an EV charger installed?

Yes, and it's worth checking before anything gets ordered. A split system, pool pump or EV charger needs spare capacity, a spare way in the board and the right protection. We check the board and the main supply first, so you're not paying for a surprise on install day.

Will a new switchboard fix my old wiring?

No. A new board protects the circuits and gives you safety switches, but it doesn't replace cable in the walls. What it does do is find problems, because the testing at changeover picks up faults an old fuse board was living with. If we find one, we'll tell you what it is and what fixing it involves.

Do you give me anything in writing when the job's done?

You get a Certificate of Testing and Compliance for the electrical work, and every circuit gets labelled with the chart filled in. If you need before and after photos for a landlord, an agent or a body corporate, just ask and we'll send them through.

Which suburbs do you cover for switchboard work?

We're based in Warner and cover Albany Creek, Eatons Hill, Cashmere, Strathpine, Petrie, Kallangur, North Lakes, Mango Hill, Narangba, Burpengary and out east to Redcliffe. Mon to Fri 7am to 5pm and Saturday mornings 7am to 11am. Call 0491 105 475.

Ready to get started?

Ring us on 0491 105 475 for a chat about what's going on, or use the form below and we'll get back to you Mon to Fri 7am to 5pm, Sat 7am to 11am.

Get in touch

Tell us what you need

Send the form or give us a call, and we'll sort out a time that suits.

Get in touch

Phone rings, we answer, we come out. For emergencies, call us straight on 0491 105 475. For everything else, fill the form or send an email.

Hours
Mon to Fri 7am to 5pm, Sat 7am to 11am

Get your free quote

Tell us about the job and we call you back.

We only use your details to call you back about this job. Privacy policy

Call 0491 105 475

Call 0491 105 475