Commercial maintenance, in plain terms
A light dies over the counter. The coffee machine circuit drops out at 7:15am. A roller door stops halfway up. None of it is dramatic. All of it costs you trade.
Commercial maintenance is the electrical work that keeps a business open. There are two halves to it. Reactive work is fault finding and repairs when something stops. Planned work is a regular visit, so the small stuff gets picked up before it drops a circuit mid shift. Most sites need a bit of both.
We look after shops, cafes, offices, warehouses, industrial sheds and small business tenancies. You can book us on a set cycle to walk the site, check the lighting and test safety switches, or ring when something breaks. Either suits us.
We're based in Warner, which keeps the runs short. Light industrial around Strathpine and Kallangur, the shopping strips and newer tenancies at North Lakes and Mango Hill, older shopfronts out on the Redcliffe peninsula, big sheds at Narangba and Burpengary, and the small offices around Albany Creek and Eatons Hill. We don't run up to Caboolture.
The north side hands us a real mix of buildings. Strip shops and sheds built in the 70s and 80s, where the switchboard has been added to five times and nobody labelled anything. Newer estate fitouts where the base build was done to a budget and the tenant then hung a commercial kitchen off it. Shopfronts near the water, where salt air eats outdoor fittings and fan housings. Each type fails in its own way. Knowing the building before we arrive saves you time on the clock.
What you get from us is simple. A time we confirm, a plain explanation of what failed, a price before we start, and the site swept before we leave.
What you notice first, and what's usually behind it
Most calls start with a symptom, not a diagnosis. That's fine. Here's what businesses on the north side usually notice, and what's normally causing it.
Lights that flicker, buzz or drop out
Old fluoro tubes go pink at the ends and start to strobe before they die. The ballast or starter is often on the way out too, so a tube swap buys you a few weeks and no more. In a warehouse, high bay fittings cop heat and dust and the driver cooks. In a cafe, downlights over the pass get hammered by steam and heat. Flicker that follows something else switching on is a different story. That points at a loose connection or an overloaded circuit, and it deserves a proper look rather than another globe.
A breaker or safety switch that keeps tripping
A safety switch, also called an RCD, cuts the power fast when current leaks where it shouldn't. When one trips again and again it's doing its job and telling you something has a fault. The usual culprits on commercial sites: a water damaged lead on a pressure washer, moisture in an outdoor power point, a dying element in a hot water unit or bain marie, a compressor drawing hard as it starts. Resetting it over and over isn't a fix. If it won't hold at all, leave the board alone and ring us.
Not enough outlets, so leads everywhere
Double adaptors piggybacked under a desk. A lead run across a doorway. A power board feeding four appliances in a kitchen. That's a sign the circuit layout hasn't kept up with how the space is actually used. Adding outlets on a properly sized circuit is usually a short job, and it takes the trip hazard away at the same time.
Exhaust fans and kitchen gear
Kitchen exhaust fans pull grease through the housing for years. Bearings dry out, the motor gets noisy, then it stops on the busiest night of the week. Office and amenities fans fail quietly, and you only notice the fogged mirror and the smell hanging around. Both are often a straight swap, but we check the duct run while the fan is out.
Corrosion and storm damage
Out at Redcliffe and along the bay, salt air gets into outdoor fittings, fan housings and every exposed screw. We pull down flood light brackets that have rusted through and weatherproof covers that crumble in your hand. Storm season across Moreton Bay brings the other batch of calls: surges that take out drivers and control gear, water tracking into a light fitting, a tripped main that won't reset. Picking gear rated for the spot it sits in is half the answer.
The switchboard itself
Plenty of older commercial boards still run rewireable ceramic fuses, or breakers with no safety switch protection at all. Boards get added to as the site changes, until there's no spare way left and no room to work. Signs it's due: a warm or discoloured board, a burnt smell, breakers tripping under normal load, labelling that no longer matches the circuits. That last one costs real money in downtime, because nobody can isolate anything quickly.
How the job runs, first call to done
No mystery to it. This is what you see.
First call. Ring Jake on 0491 105 475 and tell us what's happening, what it affects and when you trade. If you can give us the make of the gear or a photo of the board, better again.
Then we confirm a time by text or email, so you're not sitting on a vague window. We're on the tools Mon to Fri 7am to 5pm and Sat 7am to 11am, and we'll tell you straight if what you need sits outside that.
On site we sign in if you've got a visitor book or an induction, and we find out who's running the floor. Then we isolate what we need, and only what we need. Killing the whole board at 11am in a cafe isn't on when one circuit is the problem.
Fault finding is testing. We don't guess. Multimeter, clamp meter, insulation resistance tester and an RCD tester, plus a cable tracer when something's buried in a wall or ceiling. We work back from the symptom to the cause, so you're not paying for a part swap that changes nothing. If the fault is in a piece of equipment you own rather than in the wiring, we'll tell you that too.
Before the repair starts you get the options in plain words and a price. If there's a cheap fix that holds for now and a better fix that lasts, you hear both and you pick. Nothing happens on a commercial site without someone signing off.
While we work, the area gets protected. Drop sheets under the ladder, dust kept off your stock, cables run clear of customers and staff. When the work's done we test it, check trip times on any safety switch involved, label the board properly, sweep up and take our rubbish with us.
Where we've done new or altered wiring, you get a Certificate of Testing and Compliance, which is the paperwork Queensland requires from the electrical contractor for installation work.
Last part. We keep notes on your site: board layout, circuit numbering, what we replaced, what we flagged for next time. Next visit we're not starting from scratch, and you're not paying us to relearn your building.
Gear we use and the standards we work to
We buy through the trade wholesalers here on the north side, and we stick to fittings we can still get parts for in a couple of years. Cheap LED panels with sealed drivers are a false economy on a commercial site, because when one fails you're replacing the whole fitting and paying for the labour twice.
Some of what matters in the gear choice. IP rating to suit the spot, so a wash down area or an exposed wall near the water gets a properly sealed fitting, not an indoor one with a gasket. Corrosion resistant fixings close to the bay. Drivers that can be swapped on their own. Sensible colour temperature and light levels for the work being done, because a warehouse aisle and a cafe dining room aren't the same job. In switchboards, individual RCBOs so one fault doesn't take out half the site, correct torque on terminals, and labelling that matches reality.
Standards we work to:
- AS/NZS 3000, the Wiring Rules. The base standard for installation work here, covering how circuits are protected, earthed and tested.
- AS/NZS 3019, periodic verification. A checklist style inspection of an existing installation, handy when you take over a tenancy and have no idea what you've inherited.
- Queensland's electrical safety laws, which put the duty on the business running the site to keep its electrical equipment safe.
We won't sign off on something we didn't test, and we won't tell you a board complies when it doesn't. If your site needs work to get there, you get the list and a price, and you can stage it over a few visits.
When it can't wait
Straight up: we're not open around the clock. Our hours are Monday to Friday 7am to 5pm and Saturday 7am to 11am. Jake takes the calls himself, often from a job site, so if it rings out leave a message and you'll get a call back.
Inside those hours, a business with no power or no lights moves up the list. We'd rather shuffle a booked install than leave a cafe unable to trade.
What to do while you wait. If something smells burnt or hot, turn off that circuit at the board if you can do it safely, or the main switch, and leave it off. Don't keep resetting a safety switch that won't hold. Unplug whatever was running when it tripped, one item at a time, and you may well find the culprit yourself. Keep people clear of any exposed wiring or water near a board, and don't open the board. That's licensed work for a reason.
Things we treat as urgent: no power to a whole site, a board that's hot or smells like burning plastic, exposed live wiring, water in a switchboard, a safety switch that won't reset, a cool room or freezer circuit down with stock in it.
Why north side businesses call us
Rated 5.0 on Google. What we aim for is simple: turn up when we say, return calls, explain the job, leave it clean.
Jake Malcolm owns 97 Electrical and is a licensed electrician who's still on the tools every day. You're not dealing with a call centre and a different face each visit. We do the work and Jake quotes it, so nothing gets lost in a handover.
Three years in business here, and we've deliberately stayed inside the patch we can service properly: Albany Creek, Warner, Cashmere, Eatons Hill, Strathpine, Petrie, Kallangur, Mango Hill, North Lakes, Narangba, Burpengary and Redcliffe. Not Caboolture, and not all of Brisbane.
We price the job before we do it and we put it in writing. No guessing over email, because a commercial fault can be a ten minute repair or a full board upgrade, and we won't pretend to know which from a description.
Want a regular maintenance cycle? Tell us what the site is and how it trades, and we'll work out something sensible. Just want the light over the register fixed this week? That's a job too.
Ring Jake on 0491 105 475, or send the details through 97electrical.com.au. We'll confirm a time and turn up.
Frequently asked questions
What does commercial maintenance actually include?
Lighting repairs and LED changeovers, new power outlets, exhaust and ceiling fans, switchboard repairs and safety switch work, and fault finding when something trips or stops. A safety switch, or RCD, cuts the power fast if there's a fault. Tell us what's playing up and we'll tell you what's involved.
What hours do you work?
We're on the tools Mon to Fri 7am to 5pm and Sat 7am to 11am. Let us know when you trade and we'll work out a time.
What does it cost?
Depends on the site, the job and how much access we get. Give Jake a call on 0491 105 475 with the details and we'll quote it properly. No guessing over email.
Do you do regular scheduled visits or just repairs?
Both. You can book us on a set cycle to check lighting, switchboards and safety switches, or ring when something breaks. Either way we keep notes on your site, so we're not starting from scratch next visit.
Our safety switch keeps tripping. Is that urgent?
Treat it as urgent. A switch that trips again and again is telling you something has a fault, and it isn't a DIY job. Turn off what you can, leave the board alone and ring a licensed electrician on 0491 105 475.
What paperwork do we get after the job?
For new or altered wiring you get a Certificate of Testing and Compliance, which Queensland requires from the electrical contractor. For repairs you get an invoice that says what failed and what we did, in words you can hand to a property manager.
Which areas do you cover?
Albany Creek, Warner, Cashmere, Eatons Hill, Strathpine, Petrie, Kallangur, Mango Hill, North Lakes, Narangba, Burpengary and Redcliffe. We don't go up to Caboolture. Ring 0491 105 475 if you're not sure whether your site is in the patch.